The new IQOS 3 DUO has the following specifications:

- It enables two consecutive uses without Holder recharging
- Faster Holder compared to previous versions:

• At least 2min 20sec faster than charging the Holder of IQOS 2.4 Plus*
• At least 1min 40sec faster than charging the Holder of IQOS 3*
- It hosts our IQOS ProtectPlus™ System for better protection and reliability and NFC chip for easy registration and access to IQOS website.

*provided IQOS 3 DUO Holder is fully charged the first time or when fully depleted; and applicable for charging IQOS 3 DUO Holder from 0 to 1 use. It may depend on conditions of use, on battery lifecycle, weather conditions and device usage.
To check the charge level of the IQOS 3 Duo Pocket Charger, press & release the Pocket Charger Button.

The Pocket Charger Status light will turn ON for 3 sec to indicate battery status: 4 LEDs = more than 75% charged. 1 LED = low charge. Need to charge.
It takes approximately 120 minutes to fully charge the IQOS 3 DUO Pocket Charger from an electrical outlet. Only charge IQOS 3 DUO device using IQOS AC Power Adaptor and USB cable.
IQOS 3 DUO device does not require a full charge to work, however we recommend to fully charge the device before the first usage.
If the IQOS 3 DUO Pocket Charger is fully charged, you may use the Holder up to 20 times.
The Holder charging time is effective only if the IQOS 3 DUO Holder is fully charged the first time or after being fully depleted.
No, the new IQOS 3 DUO Pocket Charger is only compatible with IQOS 3.
If you insert the IQOS 2.4+ Holder into the IQOS 3 DUO Pocket Charger, the Holder will not fit because of different size.
If you accidentally insert the IQOS 3 DUO Holder in the IQOS 2.4+ Pocket Charger, the Pocket Charger lights will start blinking, however, the Holder won’t charge.
You can use the IQOS AC Power Adaptor from the previous device versions. However, IQOS 3 DUO USB cable hosts a USB-C port, which is different from that of IQOS 2.4+.
You can easily reset your IQOS 3 DUO device by pressing and holding the Pocket Charger Button for 10 seconds (until lights fade out), then releasing. All Status Lights will turn OFF, blink three times, and progressively fade in, to confirm the RESET.
You can check the Holder status (how many uses are available without recharge) in two ways – either on the Holder itself or on the Pocket Charger:

To check the status on the Holder:
- Press & release the Button of the Holder:
- 2 lights – ready for two uses
- 1 light – ready for one use
- No light – Holder not charged

To check the Holder status on the Pocket Charger:
- Press & release the Pocket Charger Button
- 2 lights – ready for two uses
- 1 light – ready for one use

On IQOS 3 DUO P. Charger
On IQOS 3 P. Charger*

* For those customers who use a mixed version of IQOS 3 DUO Holder in the IQOS 3 Pocket Charger. In some cases it may be required to upgrade the firmware of IQOS 3 Pocket Charger to know when the Holder is ready for 1 use.
IQOS 3 DUO enables to have two consecutive uses without Holder recharge. They will be indicated by the two white LED lights on your Holder and Pocket Charger.

Once you have finished the first use, there will be only one light left, i.e. 2 LEDs on – 2 uses ready, 1 LED – 1 use.

If you need the second use right away, your Holder is instantly ready for it.

If you do not need the second use right away, simply put the Holder back in the Pocket Charger for a quick recharge to have 2 uses back again.

In most cases, you can charge Holder back to at least one experience faster than Holder.

IQOS 3 DUO Holder vibrations are activated in the following situations:
- At the start of the heating (once you press the Holder Button to start) - one vibration
- When the device is ready to be used – two vibrations
- When the experience is nearly complete (30 seconds prior the end) - two vibrations
IQOS 3 DUO is designed to work in a wide range of temperatures, but HEETS tobacco stick tastes best when the device is used between 0°C and 50°C.